安裝主輕鋼龍骨

1)主龍骨應吊掛在吊桿上。主龍骨間距900～1000mm。主龍骨分為蘭州輕鋼龍骨和T 形龍骨。輕鋼龍骨可選用UC50 中龍骨和UC38 小龍骨。主龍骨應平行房間長向安裝，同時應起拱，起拱高度為房間跨度的1/200～1/300。主龍骨的懸臂段不應大于300mm，否則應增加吊桿。主龍骨的接長應采取對接，相鄰龍骨的對接接頭要相互錯開。主龍骨掛好后應基本調平。

2)跨度大于15m 以上的吊頂，應在主龍骨上，每隔15m 加一道大龍骨，并垂直主龍骨焊接牢固。

3)如有大的造型頂棚，造型部分應用角鋼或扁鋼焊接成框架，并應與樓板連接牢固。

安裝次輕鋼龍骨

次龍骨分明龍骨和暗龍骨兩種。暗龍骨吊頂：即安裝罩面板時將次龍骨封閉在棚內，在頂棚表面看不見次龍骨。明龍骨吊頂：即安裝罩面板時次龍骨明露在罩面板下，在頂棚表面能夠看見次龍骨。次龍骨應緊貼主龍骨安裝。次龍骨間距300～600mm。次龍骨分為T 形烤漆龍骨、T 形鋁合金龍骨，和各種條形扣板廠家配帶的專用龍骨。用T 形鍍鋅鐵片連接件把次龍骨固定在主龍骨上時，次龍骨的兩端應搭在L 形邊龍骨的水平翼緣上，條形扣板有專用的陰角線做邊龍骨。

V型吊掛式龍骨安裝注意

1、用于吊頂時，石膏板的長邊必須與副龍骨成垂直或平各市地鋪設，固定件(自攻螺絲)與石膏板的距離約10-16mm，緊固時，石膏板必須與骨架訂牢;

2、固定板材時，應從一塊板的中部各長邊及短邊固定，釘子定位后，釘頭略埋入板內，但不得損壞板面;

3、石膏板對接時要靠緊，接縫處必須加橫撐龍骨，石膏板應在無應力狀態下安裝，不得強壓定位，應確保副龍骨的底面處于同一平面，龍骨接長的接插部位應錯開。